Indiana Institute of Technology

Journeyman's Exam Questions And Answers 1/4" - ANS Threads of drainage fittings shall be tapped as to allow _____ pitch per foot 4 lbs - ANS Lead used for safe pans shall not be less than ________ per square foot Copper Tube, Cast Iron, Stainless steel, ABS, PVC DWV - ANS Name 3 allowable materials for the DWV system "underground" 1-1/4" - 1 dfu's 1-1/2" - 3 dfu's 2" - 4 dfu's 3" 6 dfu's 4" - dfu's - ANS What are the fixture unit values for the follow...

Journeyman Electrician Practice Test Questions And Answers Conductors with _____ marked on the insulation are NOT approved for use in a wet location. - ANS THHN conductors with THHN insulation are approved for use in dry and damp locations only and conductors with THWN, THHW, and THW insulation are recognized for use in dry and wet locations. Given: A one-family dwelling unit with a demand load of 200 amperes is supplied with a 120/240 volt, single-phase, electrical system from the ...

From beginners to advance level concepts

Journeyman's Exam With Questions And Answers | All Are Verified Solutions 1/4" Threads of drainage fittings shall be tapped as to allow _____ pitch per foot 4 lbs Lead used for safe pans shall not be less than ________ per square foot Copper Tube, Cast Iron, Stainless steel, ABS, PVC DWV Name 3 allowable materials for the DWV system "underground" 1-1/4" - 1 dfu's 1-1/2" - 3 dfu's 2" - 4 dfu's 3" 6 dfu's 4" - dfu's What are the fixture unit values for the following traps ...

NHIE Plumbing Practice Test Questions And Answers With Verified Quiz 2023 Please refer to the figure to answer this question. In the figure, the plumbing vent termination is A. installed with all proper clearances B. too close to the openable window C. too close to the property line D. too close to the wall B. too close to the openable window. A common term for the supply pipes going from the basement ceiling to the upstairs bathroom is: A. Verticals B. Stacks C. Risers D. Leaders C...

NC Plumbing Practice Test 2 Questions And Answers With Verified Solutions When using copper for vent flashing material, the copper should weigh____ 8oz/sq. ft The minimum depth of lead in a caulked joint is___ 1" Air and water tests of drainage and vent systems require that the water or air pressure be maintained at a constant level for___minutes 15 1 1/2" PVC-DWV installed in a residential building must be supported ___in the vertical. Every 10' The trap seal is the maximum vertical...

NC Plumbing Code, Fuel Gas, And Business Exam Prep Questions And Answers 2023 Licenses expires when? Last Day of December how many days in a work week 168 when license expires you have to pay within how long before you have to retake exam WITHIN 3 years or 1094 days osha form 300 A has to be posted by when feb 1st- april 30th what does flux do? thermally assist with heat transfer Physically helps in removal of metal oxides how many feet must the city sewer tap be in order to have a choi...

LP-Gas Texas Bobtail Questions And Answers With Verified Solutions Graded A+ Required for all piping systems that serve _______ psig appliance systems. normally operated at 11 in WC pressure 1/2 Required for all piping systems that serve 1/2 psig appliance systems. normally operated at ______ in WC pressure 11 Above group LP-gas containers must not be located within ____ feet of the vertical plane beneath overhead electric power lines that are over _____ volts 6 600 Fire Extinquishers m...

Journeyman Test Questions And Answers With Latest Quiz 2023 What is a journeymen plumber? any person who has practical knowledge of the installation of plumbing and installs plumbing under the direction of a master plumber APWA American Public Works Association (color code) Red Locate Electrical Power Lines, Cable, Conduit, and Lighting Cabels Yellow Gas, Oil, Steam, Petrol or Gaseous Materials Orange Communication, Alarm or signal lines, Cables or Conduit Green Sewers and Drain Lines P...

Journeyman Plumbing Test Study Guide | Complete Study Solutions Graded A+ More restrictive provisions apply where conflicts occur between code and manufacture instructions. what shall be 3rd party certified as conforming to NSF 14 all plastic pipe, fittings and components. all strainer plates on drain inlets shall be designed and installed so that all openings are..? not greater than 1/2 inch (12.7) in least dimension. pipes through foundation walls need..? a relieving arch or a pipe sle...