Weld Study guides, Class notes & Summaries

To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. - a) A transverse weld tension test. Select the cutting process that would provide the narrowest heat affected zone when cutting 12.5 mm (0.5 in) thick carbon steel. a) Oxy-acetylene cutting. b) Air-carbon arc cutting. c) Oxy-propane cutting. d) Plasma arc cutting. e) Laser beam...

CWB Welding Inspector Level 3 Exam Prep (Latest 2023/ 2024 Update) Questions and Verified Answers| All Modules Covered| 100% Correct| Grade A Q: Fluxes that can dissolve the oxides on Al are ............ Answer: Halide compounds ( Fluorine, chlorine, Bromine etc.) Q: Chlorine gas from a Chloride flux in presence of an arc can create poisonous gas called .......... Answer: Phosgene (COCL2) or Mustard gas produced by the reaction of chlorine and carbon monoxide in the prese...

CWB Welding Inspector Level 3 Exam Prep (Latest 2024 / 2025 Update) Questions and Verified Answers | All Modules Covered | 100% Correct | Grade A Q: Fluxes that can dissolve the oxides on Al are ............ Answer: Halide compounds ( Fluorine, chlorine, Bromine etc.) Q: Chlorine gas from a Chloride flux in presence of an arc can create poisonous gas called .......... Answer: Phosgene (COCL2) or Mustard gas produced by the reaction of chlorine and carbon monoxide in the presence of intense light...

What does GMAW stand for - Answer-Gas Metal Arc Welding GMAW is generally done with what polarity? - Answer-Direct current electrode positive (DC+) What type of power source is generally used for GMAW welding - Answer-Constant Voltage What does E stand for in ER70S-6 - Answer-electrode What does "70" stand for in ER70S-3? - Answer-tensile strength What mode of metal transfer allows for only flat/horizontal position GMAW welding - Answer-Spray What gas mixture is generally associated with...

CWB Welding Inspector Level 2 Exam Prep (Latest 2024 / 2025 Update) Questions and Verified Answers | All Modules Covered | 100% Correct | Grade A Q: In an isometric drawing, the lines (for width, length and depth) are inclined at an angle of how many degrees? Answer: 30° Q: What are the maximum number of views in an orthographic drawing? Answer: 6 Q: What are the two general classes of picture drawings? Answer: Perspective and Isometric Q: What are the 5 basic joints? Answer: 1) Butt 2) Corner ...

A weld having a triangular cross section which is applied to a T-joint, corner joint or lap joint is called a A) Butt B) T C) Fillet D) corner - Answer C) fillet A weld produced by filling an elongated hole in an overlapping member, fusing it to the member beneath is called a A) Flange weld B) spot weld C) seam weld D) slot weld - Answer D) slot weld True or False/ a fillet is a type of weld joint? - Answer False---- Butt T and Corners are weld joints A weld used to build up thin sur...

AMERICAN WELDING SOCIETY- CWI, WELDING INSPECTION TECHNOLOGY EXAM QUESTIONS AND ANSWERS 2024|GUARANTEED SUCCESS

Mechanical Technologist Grade 1 CWEA Certification Exam Study Guide 2024 with Verified Answers| 100% Correct| 100% Score What is an oxygen-acetylene torch? - A welding torch that uses fuel gas and oxygen to weld or cut metals What does CMMS stand for? - Computerized Maintenance Management System What does OMM stand for? - Operations and Maintenance Manual What does SOP stand for? - Standard Operating Procedure What does SCADA stand for? - Supervisory Control and Data Acquisition What doe...

1. Which is not a recommended method for surface cleaning of a part for liquid penetrant examination? a) Cleaning with organic solvents. b) Blasting with shot or dull sand. c) Cleaning with de-greasers. d) Use of de-scaling solutions. e) Ultrasonic cleaning methods. correct answersb) Blasting with shot or dull sand. 2. Which of the following weld defects is most likely to be missed by radiography in a weld: a) Undercutting. b) Porosity. c) Slag inclusions. d) Cracking. e) Burn throu...

CWB Level 1, Mod 4 - Welding Processes & High current, low voltage - correct answer Describe the current and voltage of a welding arc 30% arc heat at the electrode. 70% arc heat at the work. - correct answer What is the percentage of arc heat at the electrode and at the work when using the GTAW process with current set to DCEN? 15 degrees using a push technique - correct answer What travel angle and technique should be used with MCAW for a flat profile and good penetration? They are cla...