Brass Study guides, Class notes & Summaries

NFPA 10 Exam 99 Questions with Verified Answers (SI) - CORRECT ANSWER International System of Units 1 in=. mm - CORRECT ANSWER 25.4 Approved - CORRECT ANSWER Acceptable to the authority having jurisdiction. (AHJ) - CORRECT ANSWER Authority Having Jurisdiction O rganization, office or individual responsible for enforcing requirements of a code or standard, or for approving equipment, materials, an installation or procedure. Shall - CORRECT ANSWER Indicates a mandatory requirement....

NFPA 10 Exam 71 Questions with Verified Answers When should wheeled fire extinguishers be considered? - CORRECT ANSWER • High hazard areas are present. • Limited available personnel are present. Requiring: High agent flow rate, Increased agent stream range, increased agent capacity NON-DOT low pressure fire extinguisher cylinders that pass a hydrostatic test shall have the following recorded on a label: - CORRECT ANSWER • Month and year test was performed (perforated) • Test pre...

On an R-22 system, line diameters and lengths are typically specified for a vapor pressure drop that does not exceed what? CORRECT ANSWER 6-7PSI or 6F What is the primary purpose of using flux when soldering copper or brass parts? CORRECT ANSWER Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? CORRECT ANSWER Drain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? CORRECT ANSWER Exc...

NJ Lead Inspector/Risk Assessor Final Exam Questions with Correct Answers Graded A+ What percentage of lead is in drinking water for children? -Answer 20% What does Title X focus on? -Answer Focuses attention on source of lead that could poison children. What areas in the waterline produce high lead levels in water? -Answer Poorly Soldered joints where brass fittings are. With inspecting water what is the most causes for corrosive towards lead? -Answer Hot, Acidic and soft water W...

3B2 - Ultimate ABSA Study Guide C1-15 Study Guide Questions with Complete Solutions 100% Verified Correct Answers Latest Updated 2024/2025 Turbine nozzles convert heat energy into: a. Potential energy. b. Enthalpy. c. Eddy-currents. d. Kinetic energy. e. Pressure. - Correct Answer D Labyrinth seals are: 1. Made of cast iron. 2. A positive leak-proof seal arrangement. 3. Design to have large clearances between the shaft and casing. 4. Made of brass or stainless steel. 5. Used on lar...

NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATENCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATENCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATE unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted...

The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? Correct Answer 10% How is the main steam pressure gages tested? Correct Answer With an inspectors gage Who is in charge of the code for any plumbing installations? Correct Answer The nyc plumbing code When will anchorage or guides be inspected? Correct Answer Annually How many brass washout plugs does a miniature boiler have? Correct Answer 3 brass washout plugs, 1" in size How often i...

MUSIC APPRECIATION FINAL EMCC 100 QUESTIONS AND CORRECT ANSWERS 2023 ALL CORRECT!!! 1. The 4 main properties of musical sounds are pitch, dynamics, tone color, and?: Duration. 2. The relative highness and lowness of a sound is called?: Pitch. 3. The ____ of a sound is decided by the frequency of its vibrations.: Pitch. 4. In general, the smaller the vibrating element, the ____ its pitch:: Higher. 5. The distance in pitch between any 2 tones is called?: An Interval. 6. Dynamics in music...

When is headgear worn? - maxillary is too far forward who; remove subgingivally? - RDH who; size and fit bands? - RDA vertical measurement - overbite where is seating lug placed? - lingually horizontal measurement - overjet how long are dumbells placed for? - 30 min what is used to measure each tooth? - bow divider used to stabilize teeth in new position - retainer brass wires are used for what teeth? - posterior type of seporator - brass type of seporator - tp spring type of seporat...

Nyc high pressure boiler license Exam Questions with Correct Answers The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - Answer-10% How is the main steam pressure gages tested? - Answer-With an inspectors gage Who is in charge of the code for any plumbing installations? - Answer-The nyc plumbing code When will anchorage or guides be inspected? - Answer-Annually How many brass washout plugs does a miniature boiler have? - Answer-3 brass wa...

There are six conductors in a race way connected to 75° C rated circuit breaker. Each wire has a 70 amp load using THHM conductors. The minimum size conductors used our #_________AWG correct answer: 4 Thermal insulation shall not be installed within _________inches of recessed lighting fixtures correct answer: 3 A 1 inch conduit contains three wire circuits or a phase system. All conductors are number 10 TW. Each circuit consist of two phase conductors and one grounding conductor and on...

Lead-based paint (LBP) - Correct answer-Any varnish, shallac, or coating that contains either- 1.0 mg/cm2 - 0.5 % by weight - 5000 ppm - Older instruments could not read accurately at 0.7, so the lead standard was updated to 1.0 Dust sample clearance values - Correct answer-- Floors: 40 μg/ft2 > 10 μg/ft2 (10 μg/ft2 in NY) - Windows: 250 μg/ft2 > 100 μg/ft2 (50 μg/ft2 in NY) - Window wells (troughs): 400 μg/ft2 (100 μg/ft2 in NY) - Samples must be at 1 sq ft > 2 sq ft (can ...